Vacuum the loose dirt out of the track with a crevice tool, spray it with warm soapy water or a vinegar mix and leave it for five minutes, then scrub with an old toothbrush and wipe it out with a cloth wrapped around a butter knife or flat scraper. Finish with a dry cloth, clean the flyscreen and sill, then do the glass last.
Tracks are one of the most common items on a re-clean list in Brisbane, and it makes sense. Between dust from the road, pollen, beach sand and the odd gecko, they fill up fast, and they're right at eye level when an agent opens a window to check it works.
What you'll need
- A vacuum with a crevice tool
- A spray bottle of warm water with dishwashing liquid (or half water, half white vinegar)
- An old toothbrush or a narrow detailing brush
- A butter knife or flat plastic scraper wrapped in a cloth
- Paper towel for the dirtiest first pass, then microfibre cloths
Step by step
- Vacuum dry. Get every bit of loose dirt and insect out first. Wetting it now turns dust into mud.
- Spray and soak. Mist the track and leave it for five minutes so the stuck grime softens.
- Scrub the corners. Work the toothbrush along the channel and into each corner, where the dirt packs tightest.
- Wipe it out. Wrap a cloth around a butter knife or scraper and run it down each channel. Rinse the cloth and repeat until it comes out clean.
- Clear the weep holes. Many aluminium tracks have small drain holes on the outside. Poke them clear with a cotton bud or pipe cleaner so water can drain.
- Dry it. A dry cloth through the channel stops water marks and rust spots.

Sliding doors
Sliding door tracks take the most foot traffic in the house. Clean both the inside and outside rails, the bottom of the door itself and the rubber or brush seals. If the door drags, a clean track usually fixes it. Don't spray oil or lubricant into the track at the end of a lease; it catches dirt and looks worse by the inspection.
Flyscreens
Lift removable flyscreens out and rinse them gently with a hose, or brush them with a soft brush and soapy water. Let them dry before refitting. For fixed screens, vacuum them with the brush attachment from the inside. Note any tears on your exit condition report rather than patching them.
Sills and frames
Wipe the window sill, the frame and the latches. Timber sills in older Queenslanders hold dust in the grain, so use a damp cloth rather than a wet one.
Glass
Clean glass last. Use a squeegee with a little dishwashing liquid in water, or a microfibre glass cloth. Clean the inside of every window and the outside of ground-floor windows you can reach safely. Our bond cleans include internal windows and first-floor external glass; higher or harder-to-reach glass is a job for a professional window cleaner.
Blinds
While you're at the windows, wipe the blinds. Venetians are slow: close the slats, wipe one side, then flip and wipe the other. Vertical blinds can be wiped hanging. Fabric roller blinds usually just need a vacuum with the brush tool.
Time to allow
Plan on 10 to 20 minutes per window or door set, including tracks, screen, sill and glass. A three-bedroom house with sliding doors can easily take two to three hours just for windows. Add it up with the rest of the house in how long a bond clean takes.
For the full list of what's checked, see our bond cleaning checklist, or get a fixed price for the whole job on the prices page.
Frequently asked questions
What's the fastest way to clean window tracks?
Vacuum the loose dirt first, spray with soapy water, wait five minutes, then scrub with a toothbrush and wipe out with a cloth wrapped around a butter knife.
Do I have to clean the outside windows for a bond clean?
You're expected to clean glass you can safely reach. External glass on upper floors that needs ladders or rope access is normally a maintenance item, not tenant cleaning. Check your entry condition report.
Can I use vinegar on aluminium tracks?
Diluted vinegar is fine for a short soak. Rinse it off with plain water and dry the track so it doesn't sit on the metal.